- 5 / 22 / 55 / 180 Lumen
- CREE XP-G2 R5 LED
- Strobe and Emergency SOS Signal
- Tailcap Switch with Programmable Memory
- Type III Anodized Aluminum Housing
- Impact-Resistant and Submersible
- Reverse Polarity Protection
- Use Disposable or Rechargeable Batteries
With the addition of the second-generation CREE XP-G2 R5 LED emitter, Nitecore updated the MT1A LED Flashlight so that it now provides a higher maximum output than previous models. The MT1A is a compact light that features three normal outputs from 5 to 55 lumens, with a 180-lumen turbo mode. An intelligent two-stage pushbutton switch allows you to program your desired output, including a disorientating strobe or SOS emergency signal. To activate the turbo mode, just tighten the head slightly. This gives you access to your preferred operating output, while allowing you to quickly change to turbo mode.
Built for daily use, the aluminum housing has a scratch and corrosion-resistant hard-anodized finish, is submersible to 6.6', and impact-resistant to 5'. At just over four inches long and weighing only a few ounces, the MT1A is powerful enough to use as a primary light, yet fits comfortably in a pocket. The light runs on disposable lithium or li-ion rechargeable batteries, and there is a built-in reverse polarity protection that prevents damage to the light if the batteries are put in incorrectly.
- Light Performance
-
- 180-lumen turbo mode
- Three outputs from 5 to 55 lumens
- White CREE XP-G2 R5 LED emitter
- Tight center cone of light with large dimmer peripheral ring
- Deep, smooth aluminum reflector produces smooth beam without holes or hotspots
- SOS signal automatically cycles through Morse code sequence
- Strobe mode causes temporary blindness and disorientation
- Switching
-
- Two-stage tailcap switch and rotating body switch
- Partially press to cycle through the outputs, release to set desired output
- Click to turn on programmed output
- Turn rotary switch on the body to select Turbo, then click to activate
- Intelligent switch stores preferred brightness setting
- Construction Details
-
- Aluminum alloy housing
- Type III hard-anodized finish
- Corrosion and scratch-resistant
- Anti-reflective coated, tempered lens
- Textured diamond grip for sure handling
- Submersible to 6.6', impact-resistant to 5'
- Removable titanium-plated stainless steel clip
- U-shaped tailcap shroud helps prevent accidental activation
- Lightweight and compact design to fit comfortably in a pocket
- Compatible with lithium disposable, and li-ion rechargeable batteries
- Reverse polarity protection protects light if batteries are installed incorrectly
| Illumination Source | CREE XP-G2 R5 |
| Output Range | - Low: 5 lumen
- Med: 22 lumen
- High: 55 lumen
- Turbo: 180 lumen
|
| Battery | 1 x AA |
| Runtime | - Low: 60 h
- Med: 18 h
- High: 5.5 h
- Turbo: 1.5 h
|
| Construction | Aluminum alloy |
| Waterproofing | IPX8-rated, submersible to 6.6' (2 m) |
| Diameter | 0.9" / 2.3 cm |
| Length | 4.1" / 10.5 cm |
| Weight | 1.9 oz / 55 g |
| Packaging Info |
| Package Weight | 0.15 lb |
| Box Dimensions (LxWxH) | 6.2 x 3.9 x 1.7" |
In the Box
NITECORE MT1A v.2 LED Flashlight
- Lanyard
- O-Ring
- Stainless Steel Clip
- Spare Tailcap Boot
- Limited Lifetime Warranty
All product and company names are trademarks™ or registered® trademarks of their respective holders. Use of them does not imply any affiliation with or endorsement by them.
